One of the problems with a quartz banger and e-nail heat coil set-up is keeping the assembly together during use.
As we all remember from science class, matter expands when heated and contracts when cooled. Metal and quartz expand and contract at different rates. If the metal heat coil contracts faster than the quartz while cooling, the coil may fall off the banger. If the metal does not expand enough while heating up and is very tight around the quartz, that may result in cracking or shattering the banger. Even if it doesn’t happen the first time, repeated heating and cooling will weaken the quartz and likely form one or more cracks in your daily driver. This can also be very dangerous if flammable materials are waiting underneath your dab rig!
With the set-up pictured above we have a metal coil heating a quartz cup, so to speak. One has to fit inside the other, but not too snugly and not too loosely. This is especially true for the heating coil around the banger nail.
The early days of e-nail quartz setups featured the side-arm design (pictured above) which incorporated a quartz hook that was fused into the side of the banger itself. This proved to be difficult to get a really good fit without making it impossible to fit the coil around the bucket. The delicate arms were prone to breakage for this reason. More recently, better designs have come along to hold a coil up to a banger nail. Here we offer some handy solutions to help keep a heating coil secured to a quartz banger:
A typical quick-fix solution is using a bit of wire to secure the two parts together. Many users may prefer this fix, since the wire is easily replaced if need be. The wire bag-ties available in the produce section of a grocery store will suffice as a substitute. It’s not the prettiest solution, but it works. The only snag is disassembly after use. Rather than untwisting the wire, most users opt to simply cut the wire off and bust out a new one for the next time.
If you apply wire to secure the heater coil to the banger, you’re best off using a pair of needle-nosed pliers. Tip: making sure the tabs are completely horizontal while twisting will make a tighter connection than if they are more parallel to each other. Twist exactly like you would when closing a plastic bag, but like you mean it…
A more efficient and flexible solution has emerged. It even incorporates the humble roach clip from the old days! Cheech would be proud. This rigging uses an adjustable neoprene rubber timing belt with alligator clips to form a MacGuyver-style banger band and clip set which is highly adjustable.
The band is adjustable to fit a wide range of different axial heat coil and banger combinations. The band is made from neoprene rubber, which can withstand high temperature. It is also wire-reinforced for a second layer of protection against breakage. Although not as strong as the silicone bands (below), the band has very good heat resistance and will not produce any off-gassing if kept at least 3/4″ away from the heated part at 750F. Above that and some small particles could release (not necessarily into your rig, but better safe than sorry). As long as the band stays under (200°C), it won’t be affected. RCCtools reports that there has been one customer that has experienced breakage so far, so be smart. That being said, neoprene
is a decent material if you use it correctly, and right under silicon in heat resilience.Silicone bands are the next step up in heat tolerance. They are available in a variety of different sizes. With proper curing, silicone can withstand about 50°C degrees higher than neoprene — up to about 250°C (500°F). Silicone rubber performs superior to rubber at a wide range of temperatures, from -148° F to 572° F. Silicone is widely used in many industries for applications with an exposure to a wide range of temperatures. The hooks that hold the bands make for an easy-on, easy-off set-up
Some users might only own one banger and have no use for switching the mounting rig from one set-up to another. For a more fixed solution, these metal pins slip through the bottom of the heating coil and hold it fast to the bottom of the banger. This solution benefits from being more stable, at the sacrifice of not being as adjustable. That being said, the fit has been perfected over time. You just need to make sure your 30mm coil has a 10mm opening in the very center of the bottom to fit this nail.
An e-nail is an “electronic nail” – a titanium component that provides heat to the banger. The e-nail is a consistent way to keep your dabbing contents at a consistent temperature.
This will vary depending on your rig and preference. Experienced users recommend temperatures in the range of 500° to 600° F (260° to 315° C). Conventional wisdom holds that you should avoid temperature over 700° F (371° C). Work with your rig over time to develop a feel for the “sweet spot.”
Nope. Complete urban myth. THC is best absorbed at higher temperature in the 500+ range (see above). The difference, however, is that terpenes start burning off at temperatures as low as 300° F (148° C). So dabbing at high temperatures get you less flavor and less entourage effect. Dab at lower temperatures if you want a full-flavored effect or if the terpenes are more important to you – but you will absorb less THC.
Readers, what is your banger-coil solution? What home-made utensils have you pressed into service in a pinch? We’d love to hear all about it in the comments.
Author:
Information for this post was graciously provided courtesy of Conner at RCCtools. Your time and relative dimension in space can be found here, at the TARDIS page.
Even though I prefer to smoke my buzz, these gummies were top-shelf. I can recommend…
ColdFire carts are the real deal. If you're in Cali and you're into vaping, you…
Looking for the ultimate vaping experience in California? Look no further than Friendly Resin Disposable.…
TURN Disposable's Unicorn Party might not be the belle of the ball, but it's a…
The edible game has made another great change! Gelato has made a new sensation called…
If you're thinking about splurging on some ROVE diamond live resin pods, I'd say save…
View Comments
If you have an enail with a heated coil. I don't go over 450f or it burns it to the walls of your banger. Heated coils are the way to go. Because you can keep a consistent heat & that's important because you can easily over heat it and then it burns to the walls and if you're burning out your banger. Then it's going to get cloudy. That's never good.